G193 | Automatic gearbox hydraulic pressure sender 1 |
G194 | Automatic gearbox hydraulic pressure sender 2 |
J519 | Onboard supply control unit |
J623 | Engine control unit |
J743 | Mechatronic unit for dual clutch gearbox |
N88 | Solenoid valve 1 |
N89 | Solenoid valve 2 |
N90 | Solenoid valve 3 |
N91 | Solenoid valve 4 |
N92 | Solenoid valve 5 |
SB17 | Fuse 17 on fuse holder B |
SC25 | Fuse 25 on fuse holder C |
T20e | 20-pin connector |
T52c | 52-pin connector |
T73b | 73-pin connector |
T94 | 94-pin connector |
85 | Earth connection 1, in engine compartment wiring harness |
655 | Earth point, on left headlight |
D104 | Positive connection 2 (30a), in engine compartment wiring harness |
D109 | Connection 7 in engine compartment wiring harness |
U8 | Positive connection (15a), in automatic gearbox wiring harness |
* | see applicable current flow diagram for engine |
*2 | Only models with "High" equipment (AW1) |
*3 | Only models with "Low" equipment (AW0) |
*4 | Cross section depends on equipment |
*5 | Up to May 2012 |
G182 | Gearbox input speed sender |
G195 | Gearbox output speed sender |
G196 | Gearbox output speed sender 2 |
G487 | Gear selector movement sensor 1 |
G488 | Gear selector movement sensor 2 |
G489 | Gear selector movement sensor 3 |
G490 | Gear selector movement sensor 4 |
G501 | Input shaft speed sender 1 |
G502 | Input shaft speed sender 2 |
G509 | Clutch temperature sender |
J743 | Mechatronic unit for dual clutch gearbox |
N215 | Automatic gearbox pressure regulating valve 1 |
N216 | Automatic gearbox pressure regulating valve 2 |
N217 | Automatic gearbox pressure regulating valve 3 |
N218 | Automatic gearbox pressure regulating valve 4 |
N233 | Automatic gearbox pressure regulating valve 5 |
N371 | Automatic gearbox pressure regulating valve 6 |
T4 | 4-pin connector |
D | Ignition/starter switch |
F319 | Selector lever locked in position P switch |
G93 | Gearbox oil temperature sender |
G510 | Temperature sender in control unit |
J527 | Steering column electronics control unit |
J587 | Selector lever sensors control unit |
J743 | Mechatronic unit for dual clutch gearbox |
J764 | Control unit for electronic steering column lock |
T10 | 10-pin connector |
T10s | 10-pin connector |
T16l | 16-pin connector |
T16v | 16-pin connector |
T20e | 20-pin connector |
43 | Earth point, lower part of right A-pillar |
366 | Earth connection 1, in main wiring harness |
388 | Earth connection 23, in main wiring harness |
B114 | Connection (inhibitor switch), in interior wiring harness |
B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
* | Only models with entry and start authorisation |
*2 | According to equipment |
*3 | Only models with no entry and start authorisation |
E313 | Selector lever |
J519 | Onboard supply control unit |
J587 | Selector lever sensors control unit |
L101 | Selector lever display illumination bulb |
N110 | Selector lever lock solenoid |
SC14 | Fuse 14 on fuse holder C |
SC20 | Fuse 20 on fuse holder C |
T1fa | Single connector |
T2p | 2-pin connector |
T10s | 10-pin connector |
T10v | 10-pin connector |
T52b | 52-pin connector |
T73b | 73-pin connector |
Y6 | Selector lever position display |
A189 | Positive connection 5 (30a) in dash panel wiring harness |
A199 | Positive connection 4 (15a) in dash panel wiring harness |
B340 | Connection 1 (58d), in main wiring harness |
B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
* | Only models with "Low" equipment (AW0) |
*2 | Only models with "High" equipment (AW1) |
*3 | Up to May 2012 |
*4 | From June 2012 |
J285 | Control unit in dash panel insert |
J519 | Onboard supply control unit |
J533 | Data bus diagnostic interface |
T16 | 16-pin connector |
T20 | 20-pin connector |
T32 | 32-pin connector |
T73b | 73-pin connector |
A76 | Connection (K-diagnosis wire), in dash panel wiring harness |
B383 | Connection 1 (powertrain CAN bus, high), in main wiring harness |
B390 | Connection 1 (powertrain CAN bus, low), in main wiring harness |
B590 | K-diagnosis wire connection, in interior wiring harness |
* | Only models with "Low" equipment (AW0) |
*2 | Diagnostic connection |
*3 | Only models with "High" equipment (AW1) |