DescriptionThe front and rear door lock motors are activated simultaneously through the use of:the ignition key;the driver's front door switch (knob);the remote control.Locking operation: using the ignition key in the driver's front door, or using the remote control, when the doors are firmly shut, all the doors are locked simultaneously.Unlocking operation: using the ignition key in the driver's front door, or using the remote control, all the doors are unlocked.This operating logic is controlled by the body computer node.
Functional description The central locking function is entirely managed by the body computer node M001 which controls the locking/unlocking of the doors depending on the command received by the remote control (where available) or from the driver's front door lock N050.To lock the doors, the body computer node:from pin 12 connector H receives the negative door locking signal (with reference to earth C020 connector B) supplied by the front driver's door lock N050 (pin 6);from pin 7 connector M supplies the electric motors for the front door locks N050 and N051;from pin 10 connector E supplies the electric motors for the rear door locks N055 and N056.767 Earth C020 is fastened to the passenger compartment floor and is located near the right front wheel arch (footwell area).To unlock the doors, the body computer node:from pin 13 connector H receives the negative door unlocking signal (with reference to earth C020 connector B) supplied by the front driver's door lock N050 (pin 3);from pin 6 connector M supplies the electric motors for the front door locks N050 and N051;from pin 9 connector E supplies the electric motors for the rear doors N055 and N056.767 The power supply for the electric motors for each individual door lock (front, rear and boot) is protected by fuse F38; the door locking/unlocking logic is managed by a relay incorporated in the body computer node. The body computer supplies the electric motor for the boot lock N057 from pin 2 connector E. The command for opening the tailgate arrives from switch I033 at pin 5 connector G of the body computer node M001 (see wiring diagram E2510).The body computer node also checks that each individual door is correctly shut by means of the signals supplied by the internal (normally open type) switches for the door locks.More precisely, one door is considered as open (or not properly shut) when the body computer:receives a negative signal, from pin 23 connector H, (with reference to earth C020 connector B), coming from lock N050 (driver's front door check);receives a negative signal, from pin 21 connector H, (with reference to earth C020 connector B) coming from lock N051 (passenger front door check);receives a negative signal, from pin 4 connector G, (with reference to earth C020 connector A), coming from lock N056 (right rear door check);receives a negative signal, from pin 15 connector G, (with reference to earth C030), coming from lock N055 (left rear door check).receives a negative signal, from pin 13 connector G, (with reference to earth C030), coming from switch I033 (tailgate check, See E2510 COURTESY LIGHTS ).767 Door couplings D030 and D031 are housed in the lower part of the front pillar (right or left depending on the coupling involved), near the door cable duct.
0Removing201Refitting211. Remove the cable pass on the right side of the vehicle from itsseating and open the cover.2. Remove the adhesive tape (2a) present on the wiring (2b) andrelease the windscreen/rear window washer tubes (2c).Release the wiring from the cable pass.Following the same procedure, release thewiring from the cable pass on the left of the vehicle.2046933
5505C34
768769
5505C35
0Removing201Refitting211. Disconnect the aerial coaxial cable connections.2. Disconnect the electrical connections (2a), (2b), (2c), (2d),(2e) and (2f).2046939
0Removing201Refitting21Disconnect the battery negativeterminal.2753183-7040A23frame of instrument panel on facia - r r1. Undo the retaining bolts.Partially remove the instrument panel.2. Disconnect the electrical connection.3. Remove the instrument panel.2046983
0Removing201Refitting211. Disengage the fixing lugs (1a) and remove the cover (1b).2046919
5505A32
0Removing201Refitting21Disconnect the battery negativeterminal.2753188-7040A37fuse box cover - r r1. Undo the retaining bolts.Disconnect the electrical connections.2. Remove the body computer.2046922
0Removing201Refitting211. Rotate the clip and release the rod from the lock barrel to thelock (1a) from the lock (1b).2. Undo the retaining bolts.3. Remove the lock complete with the rod from the barrel to thelock.2047084
7015B18
0Removing201Refitting211. Undo the retaining bolts.2. Remove the striker.2047086
7015B30
0Removing201Refitting21Disconnect the battery negativeterminal.1. Disconnect the electrical connection.2. Rotate the clip and release the rod from the lock to the barrel.3. Unscrew the retaining nuts.2047088
7015B34
0Removing201Refitting211. Partly release the seal.2. Adjust the fastening clips (2a) and remove the lock barrel support(2b).767Take great care not to damagethe clips.2047090
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept All”, you consent to the use of ALL the cookies. However, you may visit "Cookie Settings" to provide a controlled consent.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.