All Wiring Diagrams for Mitsubishi Pickup Mighty Max 1994 model

AIR CONDITIONING

A/C Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for A/C Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• A/c compressor clutch (front left side of engine)
• A/c compressor clutch relay (left side of engine compartment)
• A/c controller (behind left side of dash)
• A/c engine coolant temperature switch (front of engine)
• A/c switch
• Blower motor
• Blower motor switch
• Capacitor
• Discharge gas temperature sensor (front left side of engine)
• Dual pressure switch (right front of engine compartment)
• Engine control module (right kick panel)
• Fuse 8 15a
• Fuse 9 20a
• Fuse block (right side of dash)
• Hot at all times
• Hot in run
• Hot in run and start
• Illum
• In-line fuse 10a
• Interior lights system
• Low pressure switch (right front of engine compartment)
• Nca
• Off
• Resistor (right side of dash)
• Thermistor (behind center of dash)

Heater Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Heater Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• 2.4l
• Blower motor
• Blower motor switch
• C 1995 vftc
• Capacitor
• Diode
• Engine control module
• Fuse 9 20a
• Fuse block (right side of dash)
• Hot in run
• Illum
• Interior lights system
• Nca
• Off
• Resistor (right side of dash)

ANTI-LOCK BRAKES

Anti-lock Brake Wiring Diagrams, Rear Wheel ABS for Mitsubishi Pickup Mighty Max 1994

List of elements for Anti-lock Brake Wiring Diagrams, Rear Wheel ABS for Mitsubishi Pickup Mighty Max 1994:

• (below left side of i/p)
• Data link connector (partial)
• Fuel pump
• Fuse 10a
• Fuse 15a
• Fuse block
• G sensor (under center of dash)
• G200 (left kick panel)
• G202 (left side of i/p)
• Hold valve
• Hot at all times
• Hot in run
• Hot in start and run
• Instrument cluster
• Modulator (center right side of vehicle)
• Rear abs warning ind
• Rear anti-lock brake system control unit (below center of dash)
• Red
• Release valve
• Speed sensor (rear right side of vehicle)
• Stop lamps
• Stop light switch (behind center of dash)

COMPUTER DATA LINES

Computer Data Lines for Mitsubishi Pickup Mighty Max 1994

List of elements for Computer Data Lines for Mitsubishi Pickup Mighty Max 1994:

• (below left side of i/p) data link connector
• Automatic transmission control unit (behind left side of i/p)
• Cruise control unit (left kick panel)
• Engine control module (right side of i/p)
• G202 (left side of i/p near speedometer cable)
• Instrument cluster
• Rear anti-lock brake system control unit (below center of i/p)
• Vss (reed switch)

CRUISE CONTROL

Cruise Control Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Cruise Control Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• 3.0l only
• Acc
• Actuator (rear right side of engine compartment)
• Battery
• Clutch pedal position switch (behind center of i/p)
• Cruise control switch (behind center of i/p)
• Cruise control unit (left kick panel)
• Data link connector (below left side of i/p)
• Engine control unit (behind right side of dash)
• Exterior lights system
• Fuse 3 10a
• Fuse 7 15a
• Fuse 8 15a
• Fuse block
• G106 (behind left headlight)
• G121 (center of safety wall)
• G202 (left side of i/p)
• Hot at all times
• Hot in start and run
• Ignition switch
• Instrument cluster
• Lock
• Main fusible link 60a
• Nca
• Red
• Run
• Start
• Starting system
• Stop light switch (behind center of i/p)
• Sub fusible link (left rear of engine compartment)
• Vacuum pump (rear right side of engine compartment)
• Vacuum pump relay (rear right side of engine compartment)
• Vacuum switch (rear right side of engine compartment)
• Vehicle speed sensor
• W/ abs
• Warning systems

ENGINE PERFORMANCE

2.4L

2.4L, Engine Performance Wiring Diagrams, California (1 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for 2.4L, Engine Performance Wiring Diagrams, California (1 of 2) for Mitsubishi Pickup Mighty Max 1994:

• A/c engine coolant temperature switch
• A/t
• Air conditioning compressor clutch relay
• Coil wire
• Data link connector (left side of i/p)
• Distributor firing order (1-3-4-2)
• Engine control relay (below right side of dash, at kick panel)
• Fuel injectors
• Fuel pump (in top side of fuel tank)
• Fuel pump check connector (right rear corner of engine compt)
• G106 (behind left headlamp)
• G121 (center of safety wall)
• G202 (left side of i/p)
• G203 (right kick panel)
• Ignition coil (top center of engine)
• Ignition power transistor (top center of engine)
• Ignition timing adjustment connector (right rear corner of engine compt)
• M/t
• Pnk
• Powertrain control module (below right side of dash, at kick panel)
• Pri
• Red
• Sec
• Starting system (starter relay)

2.4L, Engine Performance Wiring Diagrams, California (2 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for 2.4L, Engine Performance Wiring Diagrams, California (2 of 2) for Mitsubishi Pickup Mighty Max 1994:

• (right side of engine compt, in air cleaner assembly)
• Acc
• Egr solenoid (left side of engine compartment)
• Egr temperature sensor (left rear of engine)
• Engine coolant temperature sensor (front of engine)
• Evaporative emission purge solenoid (left side of engine compartment)
• Front heated oxygen sensor (under front of vehicle, in exhaust pipe)
• Fuse 10a
• Fuse 15a
• Fuse block
• Fusible link 2 20a
• G121 (center of safety wall)
• G202 (left side of i/p)
• G203 (right kick panel)
• Hall ic
• Hot at all times
• Idle air control motor (top rear of engine, on throttle assembly)
• Idle sw
• Ignition switch
• Instrument cluster
• Lock
• Main fusible link
• Malfunction indicator (check engine)
• Nca
• Pnk
• Rear heated oxygen sensor (under center of vehicle, in exhaust pipe)
• Red
• Start
• Starting system (starter relay)
• Throttle position sensor (top center of engine)
• Vehicle speed sensor (reed switch)
• Volume air flow sensor

2.4L, Engine Performance Wiring Diagrams, Federal (1 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for 2.4L, Engine Performance Wiring Diagrams, Federal (1 of 2) for Mitsubishi Pickup Mighty Max 1994:

• (center of safety wall)
• (check engine)
• (right kick panel)
• A/c compressor relay
• A/c engine coolant temperature switch
• A/t
• Acc
• Cluster
• Dash, at kick panel)
• Data link connector (left side of i/p)
• Engine control relay (below right side of dash, at kick panel)
• Fuel injectors
• Fuel pump (in top side of fuel
• Fuel pump check connector (right rear corner of engine compt)
• Fuse 10a
• Fuse 15a
• Fuse block
• Fusible link 2 20a
• G106 (behind left headlamp)
• G121
• G202 (left side of i/p)
• G203
• Hot at all times
• Hot in on or start
• Ig1
• Ignition switch
• Ignition timing adjust connector (right rear corner of engine compt)
• Instrument
• Instrument cluster
• Lock
• M/t
• Main fusible link (behind battery)
• Malfunction indicator
• No.1
• No.2
• No.3
• No.4
• Pnk
• Pnk
• Powertrain control module (below right side of
• Red
• Red
• Start
• Starting system (starter relay)
• Tank)
• Vehicle speed sensor (reed switch)

2.4L, Engine Performance Wiring Diagrams, Federal (2 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for 2.4L, Engine Performance Wiring Diagrams, Federal (2 of 2) for Mitsubishi Pickup Mighty Max 1994:

• (center of safety wall)
• (front of engine)
• (top center of engine)
• Coil wire
• Distributor firing order (1-3-4-2)
• Egr solenoid (left side of engine compt)
• Egr temperature sensor (left rear of engine)
• Engine coolant temperature sensor
• Evaporative emission purge solenoid (left side of engine compt)
• G121
• G203 (right kick panel)
• Idle position switch
• Idle speed control motor (top center of engine)
• Idle speed control motor position sensor (top rear of engine, on throttle assembly)
• Ignition coil
• Ignition power transistor (top center of engine)
• Nca
• Oxygen sensor (lower right side of engine)
• Pnk
• Pri
• Red
• Sec
• Throttle position sensor (top center of engine)
• Volume air flow sensor (right side of engine compt, in air cleaner assembly)

3.0L

3.0L, Engine Performance Wiring Diagrams (1 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for 3.0L, Engine Performance Wiring Diagrams (1 of 2) for Mitsubishi Pickup Mighty Max 1994:

• (center of safety wall)
• (check engine)
• (right kick
• A/c comp relay
• A/c engine coolant temperature switch
• Acc
• Cluster
• Dash, at kick panel)
• Data link connector (left side of i/p)
• Engine control module (below right side of
• Engine control relay (below right side of dash, at kick panel)
• Fuel injectors
• Fuel pump (in top side of fuel
• Fuel pump check connector (right rear corner of engine compt)
• Fuse 10a
• Fuse 15a
• Fuse block
• Fusible link 2 20a
• G106 (behind left headlamp)
• G121
• G202 (left side of i/p)
• G203
• Hot at all times
• Hot in on or start
• Ig1
• Ignition switch
• Ignition timing adjust connector (right rear corner of engine compt)
• Instrument
• Instrument cluster
• Lock
• Main fusible link (behind battery)
• Malfunction indicator
• No.1
• No.2
• No.3
• No.4
• No.5
• No.6
• Panel)
• Pnk
• Pnk
• Red
• Red
• Start
• Starter relay
• Tank)
• Vehicle speed sensor (reed switch)

3.0L, Engine Performance Wiring Diagrams (2 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for 3.0L, Engine Performance Wiring Diagrams (2 of 2) for Mitsubishi Pickup Mighty Max 1994:

• (1-2-3-4-5-6)
• (center of safety wall)
• (front of engine, near coolant outlet)
• (right kick panel)
• (top center of engine)
• California
• California models only
• Coil wire
• Distributor firing order
• Egr solenoid (left side of engine compt)
• Egr temperature sensor (left rear of engine)
• Engine coolant temperature sensor
• Evaporative emission purge solenoid (left side of engine compt)
• G121
• G203
• Heated oxygen sensor (below rear of engine, in exhaust pipe)
• Idle air control stepper motor (top right side of engine)
• Idle position switch
• Ignition coil
• Ignition power transistor (top center of engine)
• Models
• Nca
• Only
• Oxygen sensor check connector (right rear corner of engine compt)
• Pnk
• Pri
• Red
• Sec
• Throttle position sensor (top rear of engine, on throttle assembly)
• Volume air flow sensor (right side of engine compt, in air cleaner assembly)

EXTERIOR LIGHTS

Exterior Light Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Exterior Light Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• (left i/p)
• A/t
• Back-up light
• Back-up light switch (on transmission)
• Column switch
• Fuse 12 10a
• Fuse 2 15a
• Fuse 3 10a
• Fuse 7 15a
• Fuse 8 15a
• Fuse block
• G106 (behind left headlight)
• G202 (left side of i/p)
• Hazard
• Hazard switch
• Head
• High level stop light (1994 model only)
• Hot at all times
• Hot in run or start
• Instrument cluster
• Left combination light
• Left front marker light
• Left front turn light
• License lights
• Light switch
• M/t
• Nca
• Off
• P/n
• Park
• Park/neutral position switch (on transmission)
• Red
• Right combination light
• Right front marker light
• Right front turn light
• Right turn ind
• Solid state
• Stop light switch (below center of i/p)
• Stoplight
• Taillight
• Turn signal switch
• Turn signal/ hazard flasher unit (relay box) (below left side of dash)
• Turn/ hazard light

GROUND DISTRIBUTION

Ground Distribution Wiring Diagram (1 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for Ground Distribution Wiring Diagram (1 of 2) for Mitsubishi Pickup Mighty Max 1994:

• Automatic free wheeling hub indicator control unit
• Automatic transmission control unit
• Battery
• Central door lock control relay
• Cruise control module
• Cruise control switch
• Data link connector
• Engine control module
• Fuel pump
• G106 (behind battery)
• G106 (behind left headlight)
• G108 (left radiator support)
• G200 (left kick panel)
• G202 (left side of i/p)
• High level stop light (1994 models only)
• Left back-up light
• Left door lock actuator
• Left front marker light
• Left headlight
• Left license light
• Left rear combination light
• Left turn signal light
• M/t
• Power window control relay
• Power window main switch
• Power window power relay
• Pulse generator shield
• Rear anti-lock brake system control unit
• Right back-up light
• Right door lock actuator
• Right front marker light
• Right headlight
• Right license light
• Right rear combination light
• Right turn signal light
• Seat belt warning timer relay
• Speed sensor
• To modulator
• Washer motor

Ground Distribution Wiring Diagram (2 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for Ground Distribution Wiring Diagram (2 of 2) for Mitsubishi Pickup Mighty Max 1994:

• 4wd indication switch (w/ 4wd)
• Ashtray illumination light
• Brake fluid level switch
• Cigarette lighter
• Cigarette lighter illumination light
• Clock
• Clutch pedal position switch (2wd m/t)
• Dimmer control switch
• Distributor signal generator
• Egr temperature sensor (calif)
• Engine control module
• Engine control relay
• Engine coolant temperature sensor
• From g106
• Front heated oxygen sensor shield
• Fuel gauge unit
• G121 (center of safety wall) (2.4l except from 1993 for calif models)
• G121 (center of safety wall) (2.4l from 1993 models for calif)
• G121 (center of safety wall) (3.0l)
• G203 (right kick panel) (2.4l except from 1993 for calif models)
• G203 (right kick panel) (2.4l from 1993 models for calif)
• G203 (right kick panel) (3.0l)
• Heated oxygen sensor shield
• Idle air control motor shield
• Ignition power transistor
• Instrument cluster
• Modulator
• Oxygen sensor shield
• Rear heated oxygen sensor
• Rear heated oxygen sensor shield
• Starter unlock relay (4wd m/t)
• Starter unlock switch (4wd m/t)
• Throttle position sensor
• Turn signal/ hazard flasher unit
• Volume air flow sensor
• W/ tachometer only

HEADLIGHTS

Headlight Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Headlight Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• (left side of i/p, near speedometer cable)
• Air conditioning system
• B25
• Column switch
• Dimmer switch
• Engine control module (1996 2.4l) (right side of i/p)
• Fuse block (lower left front of dash)
• G111 (below battery)
• G202
• Head
• Hi-beam indicator
• Hot at all times
• Idle-up diode (1996 only) (left side of i/p)
• Instrument cluster
• Left headlight
• Lighting switch
• Multi- purpose fuse 12 10a
• Multi- purpose fuse 14 15a
• Multi- purpose fuse 15 15a
• Off
• Park
• Pass
• Pass switch
• Red
• Right headlight

HORN

Horn Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Horn Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• Column switch
• Fuse 4 10a
• Fuse block (left i/p)
• Horn
• Horn switch
• Hot in run and acc

INSTRUMENT CLUSTER

Instrument Cluster Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Instrument Cluster Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• (left i/p)
• 4wd ind (w/ 4wd)
• 4wd indicator switch (on transmission)
• A10
• A11
• A12
• Abs ind
• Auto free wheeling hub (w/ 4wd)
• Auto free wheeling hub indicator control unit (right kick panel)
• Automatic transmission control unit (on transmission)
• B10
• Beam ind
• Brake fluid level switch (left rear of engine compartment)
• Brake ind
• Charge ind
• Check engine ind
• Conn a
• Conn b
• Conn c
• Coolant temp gauge unit (left side of engine)
• Cruise control unit (left kick panel)
• Data link connector (below left side of i/p)
• Engine control module (right kick panel)
• Engine controls (noise filter)
• Fuel gauge
• Fuel gauge unit
• Fuse 7 15a
• Fuse block
• G202 (left side of i/p)
• Gauge
• Generator
• Headlights
• Hot in run
• Illumination (5 used)
• Ind
• Instrument cluster
• Interior lights system (dimmer control switch)
• Interior lights system (light switch)
• Left turn ind
• Maintenance required
• Nca
• Nca nca
• Oil
• Oil ind (w/o tach)
• Oil pressure switch (front of engine)
• Or start
• Parking brake switch (below center of i/p)
• Rear anti-lock brake system control unit (below center of dash)
• Red
• Right turn ind
• Seat belt ind
• Speed sensor (reed switch)
• Tachometer
• Temperature
• Voltage limiter
• Voltmeter
• W/ tach only
• Warning system (key remind switch)
• Warning system (seat belt warning timer relay)

INTERIOR LIGHTS

Interior Light Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Interior Light Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• (left i/p)
• Ashtray illumination light
• Blower switch illumination light
• Cigarette lighter illumination light
• Column switch
• Dimmer control switch (left side of i/p)
• Dome light (extended cab)
• Dome light (standard and long body)
• Exterior lights system (rear combination light)
• Fuse 1 10a
• Fuse 12 10a
• Fuse block
• G202 (left side of i/p)
• Hazard switch illumination light
• Head
• Hot at all times
• Instrument cluster
• Left door switch
• Light switch
• Nca
• Off
• Park
• Radio illumination light
• Right door switch

POWER DISTRIBUTION

Power Distribution Wiring Diagram (1 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for Power Distribution Wiring Diagram (1 of 2) for Mitsubishi Pickup Mighty Max 1994:

• 2.4l from 1993 models for calif only
• Acc
• Battery
• Cargo light
• Central door lock control relay
• Clock
• Cruise control unit
• Distributor signal generator (ex 3.0l)
• Dome light
• Engine control module
• Engine control module (3.0l)
• Engine control relay
• Fuse 1 10a
• Fuse 18 15a
• Fuse 2 15a
• Fuse 3 10a
• Fuse 7 15a
• Fuse block
• Generator
• Hazard switch
• Ignition coil
• Ignition switch
• Instrument cluster
• Key remind switch
• Lock
• Main fusible link 20a
• Main fusible link 60a
• Main fusible link 80a
• Power window power relay
• Radio
• Rear anti-lock brake system control unit
• Run
• Seat belt warning timer relay
• Start
• Starter
• Starter relay
• Starter unlock relay (4wd m/t)
• Starter unlock switch (4wd m/t)
• Stop light switch
• Sub fusible links
• To fuse 12
• To fuse 8
• To ignition switch
• W/ extended cab

Power Distribution Wiring Diagram (2 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for Power Distribution Wiring Diagram (2 of 2) for Mitsubishi Pickup Mighty Max 1994:

• Acc
• Air conditioning controller
• Automatic free wheeling hub indicator control unit (w/ 4wd)
• Automatic transmission control unit
• Back-up light switch (m/t)
• Blower motor switch
• Cigarette lighter
• Clock
• Column switch
• Cruise control unit
• Dimmer switch
• From a ignition switch
• From c fuse 7
• Fuse 12 10a
• Fuse 14 15a
• Fuse 15 15a
• Fuse 20 15a
• Fuse 4 10a
• Fuse 5 15a
• Fuse 6 15a
• Fuse 8 15a
• Fuse 9 20a
• Fuse block
• G202 (left side of i/p)
• Head
• Horn
• Ignition switch
• Instrument cluster
• Left headlight
• Light switch
• Lock
• Off
• Overdrive off switch (a/t)
• Overdrive solenoid valve (a/t)
• Park
• Park/ neutral position switch (a/t)
• Pass switch
• Power window power relay
• Radio
• Rear anti-lock brake system control unit
• Red
• Right headlight
• Run
• Start
• Sub-fusible links
• Wiper motor
• Wiper switch (column switch)

POWER DOOR LOCKS

Power Door Lock Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Power Door Lock Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• 1994 vftc c
• Central door lock control relay (in right door)
• Fuse 1 10a
• Fuse 18 15a
• Fuse block (left i/p)
• G106 (behind left headlight)
• G202 (right side of i/p)
• Hot at all times
• Left door lock actuator
• Right door lock actuator

POWER WINDOWS

Power Window Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Power Window Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• (left rear corner of engine compartment)
• 1994 vftc c
• Down
• Fuse 9 20a
• Fuse block (left i/p)
• G106 (behind left headlight)
• G202 (left side of i/p)
• Hot at all times
• Hot in run
• Left power window motor
• Left switch
• Lock switch
• Nca
• Power window control relay (left door)
• Power window main switch
• Power window power relay (relay box) (below left side of dash)
• Power window sub switch (right door)
• Red
• Right power window motor
• Right switch
• Solid state
• Sub fusible link

RADIO

Radio Wiring Diagrams, 2 Speaker System for Mitsubishi Pickup Mighty Max 1994

List of elements for Radio Wiring Diagrams, 2 Speaker System for Mitsubishi Pickup Mighty Max 1994:

• (1987-88)
• (1989-96)
• 1987-90
• 1991-96
• B-10
• B-11
• C-10
• C-11
• Fuse 1 10a
• Fuse 5 15a
• Fuse block
• Hot at all times
• Hot in acc or run
• Left speaker
• Nca
• Radio
• Right speaker

Radio Wiring Diagrams, 4 Speaker System for Mitsubishi Pickup Mighty Max 1994

List of elements for Radio Wiring Diagrams, 4 Speaker System for Mitsubishi Pickup Mighty Max 1994:

• (1987-88)
• (1987-90)
• (1989-90)
• (1991-96)
• 1987-90
• 1991-96
• B-10
• B-11
• C-10
• C-11
• Din cable
• Fuse 1 10a
• Fuse 5 15a
• Fuse block
• Hot at all times
• Hot in acc or run
• Left front speaker
• Left rear speaker
• Nca
• Radio
• Right front speaker
• Right rear speaker
• Tape player (1987-88)

STARTING/CHARGING

Charging Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Charging Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• Alternator
• Battery
• Charge ind
• Diode relay (left front corner of engine compartment)
• Engine controls system (ignition coil)
• Fuse 7 15a
• Fuse block
• G106 (behind left headlight)
• Hot in start and run
• Instrument cluster
• Main fusible link 20a
• Main fusible link 80a
• Starting system (starter)

Starting Wiring Diagram (1 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for Starting Wiring Diagram (1 of 2) for Mitsubishi Pickup Mighty Max 1994:

• 2wd m/t
• A/t
• A/t only
• Acc
• Battery
• Clutch pedal position switch (above clutch pedal)
• Engine control module (ecm) (behind left side of dash)
• G106 (behind left headlight)
• G202 (left side of i/p)
• Ignition switch
• Lock
• Main fusible link 60a
• P/n
• Park/neutral position switch (behind left side of i/p)
• Run
• Start
• Starter
• Starter relay (left side of i/p)
• Sub fusible link (left rear of engine compartment)

Starting Wiring Diagram, Except M/T with4-Wheel Drive for Mitsubishi Pickup Mighty Max 1994

List of elements for Starting Wiring Diagram, Except M/T with4-Wheel Drive for Mitsubishi Pickup Mighty Max 1994:

• 2wd m/t
• A/t
• A/t only
• Acc
• Battery
• Clutch pedal position switch (above clutch pedal)
• Engine control module (ecm) (behind left side of dash)
• G106 (behind left headlight)
• G202 (left side of i/p)
• Ignition switch
• Lock
• Main fusible link 60a
• P/n
• Park/neutral position switch (behind left side of i/p)
• Run
• Start
• Starter
• Starter relay (left side of i/p)
• Sub fusible link (left rear of engine compartment)

Starting Wiring Diagram, M/T with 4-Wheel Drive for Mitsubishi Pickup Mighty Max 1994

List of elements for Starting Wiring Diagram, M/T with 4-Wheel Drive for Mitsubishi Pickup Mighty Max 1994:

• Acc
• Battery
• Clutch pedal position switch (above clutch pedal)
• Fuse 15a
• Fuse block
• G106 (behind left headlight)
• G202 (left side of i/p)
• Hot in start and run
• Ignition switch
• Illum
• Ind
• Interior lights (light switch)
• Lock
• Main fusible link 60a
• Run
• Start
• Starter
• Starter relay (left side of i/p
• Starter unlock relay (left kick panel)
• Starter unlock switch (behind right side of i/p)
• Sub fusible link (left rear of engine compartment)
• Warning system (seat belt warning timer)

Starting Wiring Diagram, M/T with 4-Wheel Drive (1 of 2) for Mitsubishi Pickup Mighty Max 1994

List of elements for Starting Wiring Diagram, M/T with 4-Wheel Drive (1 of 2) for Mitsubishi Pickup Mighty Max 1994:

• Acc
• Battery
• Clutch pedal position switch (above clutch pedal)
• Fuse 15a
• Fuse block
• G106 (behind left headlight)
• G202 (left side of i/p)
• Hot in start and run
• Ignition switch
• Illum
• Ind
• Interior lights (light switch)
• Lock
• Main fusible link 60a
• Run
• Start
• Starter
• Starter relay (left side of i/p
• Starter unlock relay (left kick panel)
• Starter unlock switch (behind right side of i/p)
• Sub fusible link (left rear of engine compartment)
• Warning system (seat belt warning timer)

TRANSMISSION

Transmission Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Transmission Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• (speed sensor)
• 1995 vftc c
• Automatic transmission control unit (top of bulkhead, behind i/p)
• Diodes (below left i/p)
• Exterior lights system (back-up lights)
• Fuse 15a
• Fuse block (left i/p)
• G111 (battery tray)
• Hot in run or start
• Illum
• Instrument cluster system
• Interior lights system
• Nca
• O/d off ind
• Off
• Overdrive off switch
• Overdrive solenoid valve
• Park/neutral position switch (left side of transmission)
• Red
• Shift indicator
• Starting/ charging system (starter relay)
• Thermal switch (engine coolant) (top front of engine)
• Throttle position sensor (on throttle body)
• Torque convertor clutch solenoid
• Transmission

WARNING SYSTEMS

Warning System Wiring Diagrams for Mitsubishi Pickup Mighty Max 1994

List of elements for Warning System Wiring Diagrams for Mitsubishi Pickup Mighty Max 1994:

• (lower left front of dash)
• Buzzer
• Fuse block
• G202 (left side of i/p)
• Hot at all times
• Hot in run or start
• Instrument cluster
• Key remind switch
• Left door switch
• Multi- purpose fuse 1 10a
• Multi- purpose fuse 7 15a
• Seat belt indicator
• Seat belt switch (under left seat)
• Seat belt warning timer relay (relay box) (below left side of dash)
• Solid state

WIPER/WASHER

Wiper/Washer Wiring Diagram for Mitsubishi Pickup Mighty Max 1994

List of elements for Wiper/Washer Wiring Diagram for Mitsubishi Pickup Mighty Max 1994:

• (behind left headlight) g106
• Column switch
• Fuse 6 15a
• Fuse block (left i/p)
• G202 (left side of i/p)
• Hot in run and acc
• Int
• Intermittent wiper relay
• Off
• W/ int wiper/washer only
• Washer motor (right front corner of engine compartment)
• Washer switch
• Wiper motor (rear left side of engine compartment)
• Wiper switch