AUTOMOTIVE ELECTRICIANS PORTAL

CRUISE CONTROL – Isuzu Ascender 2003 – SYSTEM WIRING DIAGRAMS

CRUISE CONTROL

4.2L

4.2L, Cruise Control Wiring Diagram for Isuzu Ascender 2003

4.2L, Cruise Control Wiring Diagram for Isuzu Ascender 2003 https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html Automotive Electricians Portal FZCO Automotive Electricians Portal FZCO
Download PDF file

List of elements for 4.2L, Cruise Control Wiring Diagram for Isuzu Ascender 2003:

  • 5 volt ref
  • Accelerator pedal position sensor (on accelerator bracket)
  • App sensor 1
  • App sensor 2
  • B10
  • B4 c1
  • C9 c2
  • Close
  • Cruise release
  • E3 c3
  • Electronic brake control module (on inner left frame rail, adjacent to transmission)
  • Exterior lights system
  • Hot at all times
  • Hot in run
  • Hot in run & start
  • Hvac 1 fuse 39 10a
  • Ign e fuse 22 10a
  • Low ref
  • On sw
  • On/off sensor
  • On/off switch
  • Open
  • Pnk
  • Powertrain control module (pcm) (on left front of engine)
  • Rear fuse block (below left rear seat)
  • Res/accel sw
  • Res/accel switch
  • Set/coast sw
  • Set/coast switch
  • St/lp fuse 12 25a
  • Stop lamp input
  • Stoplamp switch (on brake pedal support)
  • Tac motor ctrl 1
  • Tac motor ctrl 2
  • Tan
  • Throttle body (throttle actuator control motor)
  • Tp sensor 1
  • Tp sensor 2
  • Turn signal/ multifunction switch
  • Twisted wires
  • Underhood fuse block (on left side of engine compartment)
  • Veh stop fuse 34 15a
  • Vehicle speed sensor (vss) (2wd: on right rear of transmission) (4wd: on left rear of transfer case)
  • Vehicle speed sig
  • Vss hi
  • Vss lo

5.3L

5.3L, Cruise Control Wiring Diagram for Isuzu Ascender 2003

5.3L, Cruise Control Wiring Diagram for Isuzu Ascender 2003 https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html Automotive Electricians Portal FZCO Automotive Electricians Portal FZCO
Obțineți acces la toate schemele de cablare autoDownload PDF file

List of elements for 5.3L, Cruise Control Wiring Diagram for Isuzu Ascender 2003:

  • 5 volt ref
  • Accelerator pedal position sensor (on accelerator bracket)
  • App sensor 1
  • App sensor 2
  • B10
  • B4 c1
  • C9 c2
  • Close
  • Cruise release
  • E12 c1
  • E3 c3
  • Electronic brake control module (on inner left frame rail, adjacent to transmission)
  • Etc fuse 23 15a
  • Exterior lights system
  • G108 (on lower left side of engine)
  • Ground
  • Hot at all times
  • Hot in run and start
  • Hot in run rear fuse block (below left rear seat)
  • Hvac 1 fuse 39 10a
  • Ign e fuse 22 10a
  • Ign voltage
  • Low ref
  • On sw
  • On/off sensor
  • On/off switch
  • Open
  • Pnk
  • Powertrain control module (pcm) (on left front of engine compartment)
  • Res/accel sw
  • Res/accel switch
  • Set/coast sw
  • Set/coast switch
  • St/lp fuse 12 25a
  • Stop lamp input
  • Stoplamp switch (on brake pedal support)
  • Tac motor ctrl
  • Tan
  • Throttle actuator control module (on left rear of engine compartment)
  • Throttle body (throttle actuator control motor)
  • Tp sensor 1
  • Tp sensor 2
  • Turn signal/ multifunction switch
  • Twisted wires
  • Uart serial data
  • Underhood fuse block (on left side of engine compartment)
  • Veh stop fuse 34 15a
  • Vehicle speed sensor (vss) (2wd: on right rear of transmission) (4wd: on left rear of transfer case)
  • Vehicle speed sig
  • Vss hi
  • Vss lo