TRANSMISSION
2.2L
2.2L VIN 4, A/T Wiring Diagram, 4L60-E for Chevrolet S10 Pickup 1999
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCO
List of elements for 2.2L VIN 4, A/T Wiring Diagram, 4L60-E for Chevrolet S10 Pickup 1999:
- (twisted wire pair)
- (under left side of dash) data link connector (partial)
- 1-2 shift sol
- 1-2 ss vlv ctrl
- 2-3 shift sol
- 2-3 ss vlv ctrl
- 3-2 shift sol
- 3-2 ss vlv ctrl
- A10
- A11
- Abs fuse 22 10a
- Anti-lock brakes system
- Automatic transmission (4l60-e)
- Automatic transmission fluid pressure manual valve position switch
- Automatic transmission fluid temperature sensor
- Batt
- Brake sw in
- Class ii serial
- Clstr fuse 11 10a
- Computer data lines system
- Cruise control system
- Ecm b fuse 20a
- Ecm i fuse 15a
- Ect sens gnd
- Ect sens sig
- Engine coolant temperature sensor (in coolant piping, on front of engine)
- G117 (right rear of engine)
- Gnd
- Hot at all times
- Hot in run
- Hot in run or start
- I/p fuse block
- Ign 1
- Ign g wake up
- Instrument cluster
- Malfunction indicator lamp
- Mil ctrl
- Nca
- Park/nuetral position & back up lamp switch
- Pc sol vlv ctrl hi
- Pc sol vlv ctrl lo
- Pcm ground 1
- Pcm ground 2
- Pcm ground 4
- Pnk
- Powertrain control module (on right front engine compt)
- Pressure control sol
- Radio
- Rdo batt fuse 19 10a
- Red
- Rev
- S106
- S129
- S138 (body harn, 32 cm from breakout to wiper motor)
- S140
- S152
- Solid state
- Splice pack sp201 (left side of dash below fuse block)
- Stop lamp switch
- Tan
- Tcc pwm sol
- Tcc pwm vlv ctrl
- Tcc sol
- Tcc sol vlv ctrl
- Tft sens gnd
- Tft sens sig
- Throttle position sensor (on throttle body)
- Tp sens 5v ref
- Tp sens gnd
- Tp sens sig
- Tr sw-a in
- Tr sw-b in
- Tr sw-c in
- Tr sw-p in
- Trans range-a
- Trans range-b
- Trans range-c
- Transaxle range switch (left side of trans- mission)
- Underhood fuse block
- Vehicle speed sensor (rear of transmission)
- Vss hi
- Vss lo
4WD Wiring Diagram, with 2-Speed Selectable Transfer Case for Chevrolet S10 Pickup 1999
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCOList of elements for 4WD Wiring Diagram, with 2-Speed Selectable Transfer Case for Chevrolet S10 Pickup 1999:
- (a/t only)
- (a/t) pnp switch in
- (right front of engine compt) vehicle control module (vcm)
- 12v battery
- 12v ignition (3)
- 2 door
- 2 hi request
- 2 hi status lamp
- 2wd hi indicator
- 2wd hi switch
- 4 door
- 4 hi request
- 4 hi status lamp
- 4 lo request
- 4 lo status lamp
- 4wd fuse 15 10a
- 4wd hi indicator
- 4wd hi switch
- 4wd indicator switch (on front axle, right of diff)
- 4wd lo in
- 4wd lo indicator
- 4wd lo selected
- 4wd lo switch
- Anti-lock brakes system
- Atc fuse 20a
- Body relay block (behind left side of dash)
- Btsi fuse 10a
- C10
- C11
- C12
- C13
- C14
- C15
- C16
- Crank fuse 10a
- Cruise control system
- Ctsy lp fuse 8 10a
- D10
- D11
- D12
- D13
- D14
- D15
- D16
- Data link connector
- Data link connector (dlc) (partial) (under left side of dash)
- Electronic shift transfer case
- Encoder channel a
- Encoder channel b
- Encoder channel c
- Encoder channel p
- Encoder channel-a
- Encoder channel-b
- Encoder channel-c
- Encoder channel-p
- Encoder ground
- Encoder signal ground
- G201 (right side of dash)
- Hot at all times
- Hot in park or neutral
- Hot in run
- Hot in start
- I/p fuse block (on left end of dash)
- Ign 3
- Ignition
- Illumination lamp
- Interior lights system
- Interior lights system, sound systems, srs system
- M shift motor
- Motor control a
- Motor control b
- Motor ground
- Power ground
- Red
- S121 (body harn, 6.5 cm from blower motor breakout)
- S208
- Solid state
- Splice pack sp204 (center of dash)
- Splice pack sp200 (center of dash)
- Splice pack sp203 (near ashtray)
- Splice pack sp204 (center of dash)
- Starting/ charging system
- Stoplight switch
- Transfer case shift control module (behind right front kick panel)
- Transfer case shift control switch
- Underhood fuse block (on top of left front fender)
- Vehicle spd out
- Vehicle speed in
- Wheel lck in
4.3L
4.3L VIN W, A/T Wiring Diagram, 4L60-E for Chevrolet S10 Pickup 1999
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCOList of elements for 4.3L VIN W, A/T Wiring Diagram, 4L60-E for Chevrolet S10 Pickup 1999:
- (center of dash) splice pack sp200
- (engine harn, 8 cm from breakout to generator) s102
- (not used)
- (twisted wire pair)
- (w/ auto a/c)
- (w/ manual a/c)
- 1-2 shift sol
- 1-2 shift sol ctrl
- 2-3 shift sol
- 2-3 shift sol ctrl
- 2wd
- 3-2 shift sol
- 3-2 sol ctrl
- 4wd
- 5v reference
- A/t fluid pressure manual valve position switch
- A10
- A11
- Abs
- All times
- Anti-lock brakes system
- Automatic transmission (4l60-e)
- B10
- Battery feed
- Brake signal
- Clstr
- Cruise control system
- Data link connector (partial) (below left side of dash)
- Ecm b
- Ecm i fuse 15a
- Ect signal
- Engine controls system
- Engine coolant temperature sensor (between left two rear spark plugs)
- Fuse 11 10a
- Fuse 15 10a
- Fuse 20a
- Fuse 22 10a
- G114 (rear of left cylinder head)
- G116 (left side of firewall)
- Hot at
- Hot in
- Hot in run
- Hot in run, off
- I/p fuse block
- I/p fuse block (left side of dash)
- Ignition control module
- Ignition feed
- Instrument cluster
- Junction connector c116 (near top rear of transmission)
- Malfunction indicator lamp
- Mil ctrl
- Nca
- Or start
- Pnk
- Press ctrl so hi
- Press ctrl sol lo
- Pressure control solenoid
- Radio
- Radio & electronic climate control module
- Range signal-a
- Range signal-b
- Range signal-c
- Rdo batt fuse 15 15a
- Red
- Rev
- Run
- Run feed
- S100 (engine harn, 30 cm from breakout to vcm)
- S106
- S113
- S134
- S138 (body harn, approx 32 cm from breakout to wiper motor )
- S140
- S240
- Sensor ground
- Serial data
- Solid state
- Splice pack sp201 (left side of dash)
- Stop lamp switch
- System gnd
- Tan
- Tcc pwm sol
- Tcc pwm sol ctrl
- Tcc sol
- Tcc sol ctrl
- Tft signal
- Throttle position sensor (on throttle body)
- Tp signal
- Transmission fluid temperature sensor
- Underhood fuse block
- Vehicle control module (right front of engine compt)
- Vehicle speed sensor (4wd) (on transfer case)
- Vehicle speed sensor) (2wd) (rear of transmission)
- Vss hi
- Vss lo
4.3L VIN X, A/T Wiring Diagram, 4L60-E for Chevrolet S10 Pickup 1999
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCOList of elements for 4.3L VIN X, A/T Wiring Diagram, 4L60-E for Chevrolet S10 Pickup 1999:
- (center of dash) splice pack sp200
- (engine harn, 8 cm from breakout to generator) s102
- (not used)
- (twisted wire pair)
- (w/ auto a/c)
- (w/ manual a/c)
- 1-2 shift sol
- 1-2 shift sol ctrl
- 2-3 shift sol
- 2-3 shift sol ctrl
- 2wd
- 3-2 shift sol
- 3-2 sol ctrl
- 4wd
- 5v reference
- A/t fluid pressure manual valve position switch
- A10
- A11
- Abs
- All times
- Anti-lock brakes system
- Automatic transmission (4l60-e)
- B10
- Battery feed
- Brake signal
- Clstr
- Cruise control system
- Data link connector (partial) (below left side of dash)
- Ecm b
- Ecm i fuse 15a
- Ect signal
- Engine controls system
- Engine coolant temperature sensor (between left two rear spark plugs)
- Fuse 11 10a
- Fuse 15 10a
- Fuse 20a
- Fuse 22 10a
- G114 (rear of left cylinder head)
- G116 (left side of firewall)
- Hot at
- Hot in
- Hot in run
- Hot in run, off
- I/p fuse block
- I/p fuse block (left side of dash)
- Ignition control module
- Ignition feed
- Instrument cluster
- Junction connector c116 (near top rear of transmission)
- Malfunction indicator lamp
- Mil ctrl
- Nca
- Or start
- Pnk
- Press ctrl so hi
- Press ctrl sol lo
- Pressure control solenoid
- Radio
- Radio & electronic climate control module
- Range signal-a
- Range signal-b
- Range signal-c
- Rdo batt fuse 15 15a
- Red
- Rev
- Run
- Run feed
- S100 (engine harn, 30 cm from breakout to vcm)
- S106
- S113
- S134
- S138 (body harn, approx 32 cm from breakout to wiper motor )
- S140
- S240
- Sensor ground
- Serial data
- Solid state
- Splice pack sp201 (left side of dash)
- Stop lamp switch
- System gnd
- Tan
- Tcc pwm sol
- Tcc pwm sol ctrl
- Tcc sol
- Tcc sol ctrl
- Tft signal
- Throttle position sensor (on throttle body)
- Tp signal
- Transmission fluid temperature sensor
- Underhood fuse block
- Vehicle control module (right front of engine compt)
- Vehicle speed sensor (4wd) (on transfer case)
- Vehicle speed sensor) (2wd) (rear of transmission)
- Vss hi
- Vss lo
4WD Wiring Diagram, with 2-Speed Selectable Transfer Case for Chevrolet S10 Pickup 1999
https://portal-diagnostov.com/license.html
https://portal-diagnostov.com/license.html
Automotive Electricians Portal FZCO
Automotive Electricians Portal FZCOList of elements for 4WD Wiring Diagram, with 2-Speed Selectable Transfer Case for Chevrolet S10 Pickup 1999:
- (a/t only)
- (a/t) pnp switch in
- (right front of engine compt) vehicle control module (vcm)
- 12v battery
- 12v ignition (3)
- 2 door
- 2 hi request
- 2 hi status lamp
- 2wd hi indicator
- 2wd hi switch
- 4 door
- 4 hi request
- 4 hi status lamp
- 4 lo request
- 4 lo status lamp
- 4wd fuse 15 10a
- 4wd hi indicator
- 4wd hi switch
- 4wd indicator switch (on front axle, right of diff)
- 4wd lo in
- 4wd lo indicator
- 4wd lo selected
- 4wd lo switch
- Anti-lock brakes system
- Atc fuse 20a
- Body relay block (behind left side of dash)
- Btsi fuse 10a
- C10
- C11
- C12
- C13
- C14
- C15
- C16
- Crank fuse 10a
- Cruise control system
- Ctsy lp fuse 8 10a
- D10
- D11
- D12
- D13
- D14
- D15
- D16
- Data link connector
- Data link connector (dlc) (partial) (under left side of dash)
- Electronic shift transfer case
- Encoder channel a
- Encoder channel b
- Encoder channel c
- Encoder channel p
- Encoder channel-a
- Encoder channel-b
- Encoder channel-c
- Encoder channel-p
- Encoder ground
- Encoder signal ground
- G201 (right side of dash)
- Hot at all times
- Hot in park or neutral
- Hot in run
- Hot in start
- I/p fuse block (on left end of dash)
- Ign 3
- Ignition
- Illumination lamp
- Interior lights system
- Interior lights system, sound systems, srs system
- M shift motor
- Motor control a
- Motor control b
- Motor ground
- Power ground
- Red
- S121 (body harn, 6.5 cm from blower motor breakout)
- S208
- Solid state
- Splice pack sp204 (center of dash)
- Splice pack sp200 (center of dash)
- Splice pack sp203 (near ashtray)
- Splice pack sp204 (center of dash)
- Starting/ charging system
- Stoplight switch
- Transfer case shift control module (behind right front kick panel)
- Transfer case shift control switch
- Underhood fuse block (on top of left front fender)
- Vehicle spd out
- Vehicle speed in
- Wheel lck in
Čeština
Dansk
Deutsch
Ελληνικά
English
English
Español
Suomi
Français
Français
עברית
Hrvatski
Magyar
Italiano
한국어
Nederlands
Polski
Português
Português
Română
Русский
Slovenčina
Slovenščina
Svenska
Türkçe
中文 (中国)
