TRANSMISSION – Ford Ranger 1995 – SYSTEM WIRING DIAGRAMS

TRANSMISSION

2.3L

2.3L, Transmission Wiring Diagram for Ford Ranger 1995

List of elements for 2.3L, Transmission Wiring Diagram for Ford Ranger 1995:

• (dash panel to headlamp junction harness, near break out to left headlamp)
• (engine control sensor extension harness, near break out to harness in-line connector, left rear of engine)
• (engine control sensor harness, in break out to harness in-line connector, left rear of engine)
• (engine control sensor harness, near break out to ground g123, right side of safety wall)
• (engine control sensor harness, near break out to intake air temperature (iat) sensor
• (engine control sensor harness, near break out to throttle position (tp) sensor)
• (left side of upper radiator support) g108
• (left side of transmission) transmission range (tr) sensor
• (left side of upper radiator support) g108
• (power for heated oxygen sensors)
• (right side of safety wall) g123
• (top center of left fender apron) g104
• Boo
• Brake on/off (boo) switch (on brake pedal support)
• C111
• C214
• C216
• Case gnd
• Ccs
• Coast clutch solenoid (ccs)
• Cse gnd
• Dlc
• Dlc (+)
• Dlc (-)
• Ect
• Electronic pressure control (epc) solenoid
• Engine air cleaner assembly
• Engine compartment fuse/relay box
• Engine coolant temperature (ect) sensor (top right front of engine, in water outlet tube)
• Epc
• Fuse 13 15a
• Fuse 19 25a
• Fuse 26 15a
• Ho2s fuse 20 15a
• Horn/pcm memory power fuse 4 20a
• Hot at all times
• Hot in run
• Hot in start or run
• I/p fuse panel
• Iat
• Instrument cluster
• Intake air temperature (iat) sensor (right side of engine compartment, on air intake assembly)
• Kapwr
• Maf
• Maf rtn
• Malfunction indicator lamp (mil)
• Mass air flow (maf) sensor
• Mil
• N d
• O/d off
• Pcm power diode
• Pcm power fuse 13 30a
• Pcm power relay
• Powertrain control module (pcm) (right rear of engine compartment, through safety wall)
• Pwr gnd
• Red
• S100
• S1002
• S1003
• S102 (engine control sensor harness, near break out to intake air temperature (iat) sensor)
• S103
• S104
• S106
• S108
• S110
• S111
• S118
• S121
• S134
• S135
• S142 (dash panel to headlamp junction harness, in break out to harness in-line connector, left side of safety wall)
• Shift solenoid (ss1)
• Shift solenoid (ss2)
• Shift solenoid (ss3)
• Sig rtn
• Ss1
• Ss2
• Ss3
• Tcc
• Tcil
• Tcs
• Tft
• Throttle position (tp) sensor (top right side of engine, on throttle body)
• Torque converter clutch (tcc) solenoid
• Transmission (4r44e/4r55e) (left side of transmission)
• Transmission control indicator lamp (tcil)
• Transmission control switch (tcs)
• Transmission fluid temperature (tft) sensor
• Tss
• Turbine shaft speed sensor (tss)
• Vehicle speed sensor (vss) (left rear of transmission) (4x2 models) (left rear of transfer case) (4x4 models)
• Vpwr
• Vref
• Vss

Transfer Case Wiring Diagram for Ford Ranger 1995

List of elements for Transfer Case Wiring Diagram for Ford Ranger 1995:

• (behind i/p, right side of steering column) relay box 1
• (main harness, in break out to generic electronic module (gem) connectors)
• (main harness, near break out to i/p fuse panel)
• (top center of left fender apron) g104
• 1.1k ohms
• 1995 models
• 1996 models
• 3.9k ohms
• 4 wheel drive fuse 16 20a
• 4wd hi ind
• 4wd ind ctrl
• 4wd lo ind
• 4wd mode sw
• 4wd mode switch
• 4wd motor
• 4wd output
• Battery saver relay
• Boo sw input
• Brake on/off (boo) switch (on brake pedal support)
• C214
• C221
• C223
• C224
• Ccw relay
• Ccw rly ctrl
• Clutch
• Cw relay
• Cw rly ctrl
• Elc rly ctrl
• Electric shift control module (behind center of i/p)
• Electric shift relay
• Engine compartment fuse/relay box
• Fuse 13 15a
• Fuse 27 15a (1995 models) 10a (1996 models)
• G104 (top center of left fender apron)
• Generic electronic module (gem) (behind center of i/p)
• Hot at all times
• I/p fuse panel
• Illumination
• Instrument cluster
• Interior lights system (instrument illum- ination circuit)
• Nca
• Neutral sw in
• Ohms
• Park lamps fuse 7 20a
• Pin out for 1995 models only
• Pin out for 1996 models only
• Pnk
• Relay box 1 (behind i/p, right side of steering column)
• Rly ctrl
• S107
• S209
• S215
• S216
• S218
• S221
• S224
• S228 (main harness, near break out to instrument cluster connectors)
• S237
• Sw a input
• Sw b input
• Sw c input
• Sw d input
• Touch drive
• Transfer case assembly (below vehicle, behind transmission)
• Transmission range (tr) sensor (left side of transmission)
• Wall) g123

3.0L

3.0L, Transmission Wiring Diagram for Ford Ranger 1995

List of elements for 3.0L, Transmission Wiring Diagram for Ford Ranger 1995:

• (dash panel to headlamp junction harness, near break out to left headlamp)
• (engine control sensor extension harness, near break out to harness in-line connector, left rear of engine)
• (engine control sensor harness, in break out to differential pressure feedback egr (dpfe) sensor)
• (engine control sensor harness, in break out to harness in-line connector, rear of engine, top of transmission bell housing)
• (engine control sensor harness, near break out to differential pressure feedback egr (dpfe) sensor) s102
• (engine control sensor harness, near break out to egr vacuum regulator (evr) solenoid)
• (engine control sensor harness, near break out to harness in-line connector, left rear of engine) s104
• (engine control sensor harness, near break out to octane adjust shorting bar) s103
• (engine control sensor harness, near break out, to harness in-line connector, left rear of engine)
• (left side of upper radiator support) g108
• (left side of transmission) transmission range (tr) sensor
• (left side of upper radiator support) g108
• (power for heated oxygen sensors)
• (right side of safety wall) g123
• (top center of left fender apron) g104
• Boo
• Brake on/off (boo) switch (on brake pedal support)
• C111
• C214
• C216
• Case gnd
• Ccs
• Coast clutch solenoid (ccs)
• Cse gnd
• Dlc
• Dlc (+)
• Dlc (-)
• Ect
• Electronic pressure control (epc) solenoid
• Engine air cleaner assembly
• Engine compartment fuse/relay box
• Engine coolant temperature (ect) sensor (top front of engine)
• Epc
• Fuse 13 15a
• Fuse 19 25a
• Fuse 26 15a
• Ho2s fuse 20 15a
• Horn/pcm memory power fuse 4 20a
• Hot at all times
• Hot in run
• Hot in start or run
• I/p fuse panel
• Iat
• Instrument cluster
• Intake air temperature (iat) sensor (right side of engine compartment, on air intake assembly)
• Kapwr
• Maf
• Maf rtn
• Malfunction indicator lamp (mil)
• Mass air flow (maf) sensor
• Mil
• N d
• O/d off
• Pcm power diode
• Pcm power fuse 13 30a
• Pcm power relay
• Powertrain control module (pcm) (right rear of engine compartment, through safety wall)
• Pwr gnd
• Red
• S100
• S1002
• S1003
• S106
• S108
• S110
• S111
• S112 (engine control sensor harness, near break out to octane adjust shorting bar)
• S113
• S118
• S121
• S134
• S135
• S142 (dash panel to headlamp junction harness, in break out to harness in-line connector, left side of safety wall)
• Shift solenoid (ss1)
• Shift solenoid (ss2)
• Shift solenoid (ss3)
• Sig rtn
• Ss1
• Ss2
• Ss3
• Tcc
• Tcil
• Tcs
• Tft
• Throttle position (tp) sensor (top left front of engine, on throttle body)
• Torque converter clutch (tcc) solenoid
• Transmission (4r44e/4r55e) (left side of transmission)
• Transmission control indicator lamp (tcil)
• Transmission control switch (tcs)
• Transmission fluid temperature (tft) sensor
• Tss
• Turbine shaft speed sensor (tss)
• Vehicle speed sensor (vss) (left rear of transmission) (4x2 models) (left rear of transfer case) (4x4 models)
• Vpwr
• Vref
• Vss

Transfer Case Wiring Diagram for Ford Ranger 1995

List of elements for Transfer Case Wiring Diagram for Ford Ranger 1995:

• (behind i/p, right side of steering column) relay box 1
• (main harness, in break out to generic electronic module (gem) connectors)
• (main harness, near break out to i/p fuse panel)
• (top center of left fender apron) g104
• 1.1k ohms
• 1995 models
• 1996 models
• 3.9k ohms
• 4 wheel drive fuse 16 20a
• 4wd hi ind
• 4wd ind ctrl
• 4wd lo ind
• 4wd mode sw
• 4wd mode switch
• 4wd motor
• 4wd output
• Battery saver relay
• Boo sw input
• Brake on/off (boo) switch (on brake pedal support)
• C214
• C221
• C223
• C224
• Ccw relay
• Ccw rly ctrl
• Clutch
• Cw relay
• Cw rly ctrl
• Elc rly ctrl
• Electric shift control module (behind center of i/p)
• Electric shift relay
• Engine compartment fuse/relay box
• Fuse 13 15a
• Fuse 27 15a (1995 models) 10a (1996 models)
• G104 (top center of left fender apron)
• Generic electronic module (gem) (behind center of i/p)
• Hot at all times
• I/p fuse panel
• Illumination
• Instrument cluster
• Interior lights system (instrument illum- ination circuit)
• Nca
• Neutral sw in
• Ohms
• Park lamps fuse 7 20a
• Pin out for 1995 models only
• Pin out for 1996 models only
• Pnk
• Relay box 1 (behind i/p, right side of steering column)
• Rly ctrl
• S107
• S209
• S215
• S216
• S218
• S221
• S224
• S228 (main harness, near break out to instrument cluster connectors)
• S237
• Sw a input
• Sw b input
• Sw c input
• Sw d input
• Touch drive
• Transfer case assembly (below vehicle, behind transmission)
• Transmission range (tr) sensor (left side of transmission)
• Wall) g123

4.0L

4.0L, Transmission Wiring Diagram for Ford Ranger 1995

List of elements for 4.0L, Transmission Wiring Diagram for Ford Ranger 1995:

• (dash panel to headlamp junction harness, near break out to left headlamp)
• (engine control sensor extension harness, near break out to harness in-line connector, left rear of engine)
• (engine control sensor harness, in break out to differential pressure feedback egr (dpfe) sensor)
• (engine control sensor harness, in break out to harness in-line connector, rear of engine, top of transmission bell housing)
• (engine control sensor harness, near break out to fuel injector 5) s102
• (engine control sensor harness, near break out to fuel injector 5) s104
• (engine control sensor harness, near break out to fuel injector 6)
• (engine control sensor harness, near break out to fuel injector 6) s103
• (engine control sensor harness, near break out to mass air flow (maf) sensor)
• (left side of upper radiator support) g108
• (left side of transmission) transmission range (tr) sensor
• (left side of upper radiator support) g108
• (power for heated oxygen sensors)
• (right side of safety wall) g123
• (top center of left fender apron) g104
• Boo
• Brake on/off (boo) switch (on brake pedal support)
• C111
• C214
• C216
• Case gnd
• Ccs
• Coast clutch solenoid (ccs)
• Cse gnd
• Dlc
• Dlc (+)
• Dlc (-)
• Ect
• Electronic pressure control (epc) solenoid
• Engine air cleaner assembly
• Engine compartment fuse/relay box
• Engine coolant temperature (ect) sensor (top front of engine)
• Epc
• Fuse 13 15a
• Fuse 19 25a
• Fuse 26 15a
• Ho2s fuse 20 15a
• Horn/pcm memory power fuse 4 20a
• Hot at all times
• Hot in run
• Hot in start or run
• I/p fuse panel
• Iat
• Instrument cluster
• Intake air temperature (iat) sensor (front of engine, on air intake assembly)
• Kapwr
• Maf
• Maf rtn
• Malfunction indicator lamp (mil)
• Mass air flow (maf) sensor
• Mil
• N d
• O/d off
• Pcm power diode
• Pcm power fuse 13 30a
• Pcm power relay
• Powertrain control module (pcm) (right rear of engine compartment, through safety wall)
• Pwr gnd
• Red
• S100
• S1002
• S1003
• S106
• S108
• S110
• S111
• S112 (engine control sensor harness, in break- out to powertrain control module)
• S113
• S118
• S121
• S134
• S135
• S142 (dash panel to headlamp junction harness, in break out to harness in-line connector, left side of safety wall)
• Shift solenoid (ss1)
• Shift solenoid (ss2)
• Shift solenoid (ss3)
• Sig rtn
• Ss1
• Ss2
• Ss3
• Tcc
• Tcil
• Tcs
• Tft
• Throttle position (tp) sensor (top left front of engine, on throttle body)
• Torque converter clutch (tcc) solenoid
• Transmission (4r44e/4r55e) (left side of transmission)
• Transmission control indicator lamp (tcil)
• Transmission control switch (tcs)
• Transmission fluid temperature (tft) sensor
• Tss
• Turbine shaft speed sensor (tss)
• Vehicle speed sensor (vss) (left rear of transmission) (4x2 models) (left rear of transfer case) (4x4 models)
• Vpwr
• Vref
• Vss

Transfer Case Wiring Diagram for Ford Ranger 1995

List of elements for Transfer Case Wiring Diagram for Ford Ranger 1995:

• (behind i/p, right side of steering column) relay box 1
• (main harness, in break out to generic electronic module (gem) connectors)
• (main harness, near break out to i/p fuse panel)
• (top center of left fender apron) g104
• 1.1k ohms
• 1995 models
• 1996 models
• 3.9k ohms
• 4 wheel drive fuse 16 20a
• 4wd hi ind
• 4wd ind ctrl
• 4wd lo ind
• 4wd mode sw
• 4wd mode switch
• 4wd motor
• 4wd output
• Battery saver relay
• Boo sw input
• Brake on/off (boo) switch (on brake pedal support)
• C214
• C221
• C223
• C224
• Ccw relay
• Ccw rly ctrl
• Clutch
• Cw relay
• Cw rly ctrl
• Elc rly ctrl
• Electric shift control module (behind center of i/p)
• Electric shift relay
• Engine compartment fuse/relay box
• Fuse 13 15a
• Fuse 27 15a (1995 models) 10a (1996 models)
• G104 (top center of left fender apron)
• Generic electronic module (gem) (behind center of i/p)
• Hot at all times
• I/p fuse panel
• Illumination
• Instrument cluster
• Interior lights system (instrument illum- ination circuit)
• Nca
• Neutral sw in
• Ohms
• Park lamps fuse 7 20a
• Pin out for 1995 models only
• Pin out for 1996 models only
• Pnk
• Relay box 1 (behind i/p, right side of steering column)
• Rly ctrl
• S107
• S209
• S215
• S216
• S218
• S221
• S224
• S228 (main harness, near break out to instrument cluster connectors)
• S237
• Sw a input
• Sw b input
• Sw c input
• Sw d input
• Touch drive
• Transfer case assembly (below vehicle, behind transmission)
• Transmission range (tr) sensor (left side of transmission)
• Wall) g123